45 English reviews written for 3DJAKE ecoPLA White
382 customer reviews in all languages
| 5 stars | | 672 | (74%) |
|---|---|---|---|
| 4 stars | | 125 | (13%) |
| 3 stars | | 41 | (4%) |
| 2 stars | | 26 | (2%) |
| 1 Stars | | 44 | (4%) |
Filter reviews:
-
Osprey
12 May 2025
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. -
Printer
11 January 2025
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Poor adhesion, small artifacts, nice finish
Rated with 3 out of 5 stars.
It's ok for the price. I like the look of the material, e.g. it's less translucent Prusament PLA Pristine White.
However I had many issues with bed adhesion on a smooth PEI as well as satin and textured beds. Additionally there's often a small amount of stringing even after drying it for a really long time. E.g. benchy typically will not stick to the bed; I used brim for most of my prints to combat this. Large flat parts wrap and detach from the bed easily.
The plastic spools are quite heavy, it's a pity to waste such a large amount of plastic.
After printing the temperature tower I set: Nozzle temperature 220 for the 1st layer, 215 for other layers. I also set retraction length in filament overrides to 1.2mm to reduce stringing (printer Prusa mk4s), not sure if that helped.
Since I couldn't find perfect settings I think I'll go back to prusaments. The price is good, but if I had to fiddle with adhesion every print it's not worth it.Was this rating helpful? (0) (0)
-
SIMONZ
10 December 2024
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. SIMONZ
Rated with 5 out of 5 stars.
Good reliable filament, great consistent results
Was this rating helpful? (0) (0)
-
Jaime
13 October 2024
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Requires adjustment
Rated with 3 out of 5 stars.
I am a beginner in this world but still, this filament took me long time to get right. I usually print with PLA or PLA+ and don't need to adjust much. Here, as others mentioned in the comments, you need to increase the temperature to at least 215 and the bed to 60 to get adhesion and increase the flow. Only then I managed to print.
Was this rating helpful? (0) (0)
-
Gadget
09 August 2024
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Undecided
Rated with 3 out of 5 stars.
So I can't get this to print well at all on my Creality K1, 95% of the time it doesn't even stick to the build plate. My Bambu X1C on the other hand prints it perfectly fine with their basic PLA profile loaded.
Was this rating helpful? (0) (0)
-
Mike
02 June 2024
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Utterly Useless Landfill Generator
Rated with 1 out of 5 stars.
This stuff is the ideal gift for someone you hate. It is essentially unusable. After a few hundred failed prints & 3 or 4 that were usable (with a lot of sanding & postwork) I have just thrown half a spool of this in the bin. Never again.
lmao it's ur settings bro
Nope. Swap the spool for a spool of esun (which is actually CHEAPER than this junk) and everything prints perfectly. Exact same gcode.
It will not stick to the bed.
It warps. Badly.
If you do get a print to finish, the top surface is unacceptable. Spiky, jagged lumps everywhere. Even layer adhesion is terrible. The few prints that actually completed did so with big holes ripped in the sides that look like the bonnet louvres on a 1920s race car. Same gcode prints perfectly with the esun stuff.
There is no amount of settings adjustment, bed levelling or printer setup that can make this stuff work. It is quite simply a bad, bad product. Avoid it at all costs... Unless you have a smug friend who constantly waffles on about how great his printer is, then get him some of this for xmas and watch his interest in the hobby die.Was this rating helpful? (1) (0)
-
TheMinjus
15 May 2024
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Love it!
Rated with 5 out of 5 stars.
Very reliable!
Was this rating helpful? (0) (0)
-
Derek Owen
12 February 2024
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Derek Owen
Rated with 5 out of 5 stars.
great filament
Was this rating helpful? (0) (0)
-
Lars
05 January 2024
"Verified Purchase" indicates that the rating was given by customers who actually bought this product from us. However, anyone who has a customer account with us can give a rating. Bad tolerances and knots
Rated with 1 out of 5 stars.
Awful product. Would never buy. First 20-30m ok, after that I had two failed prints because the filament had larger parts and could not get extruded. Also twice I had to pause and remove a knot in the filament.
Was this rating helpful? (0) (0)
-
Works well enough with the Bambulab P1S after tweaks
Rated with 4 out of 5 stars.
Had to tweak some settings to get this printing well on the high-speed Bambulab P1S. Turning down the flow ratio (to prevent overextrusion) of the "generic PLA" preset helped a lot. It works, if still slightly sloppily. And with the lack of in-supply filament in Bambu's store this filament'll fill the gap nicely enough.
Was this rating helpful? (1) (0)
Magazine Articles:
Discover 3DJake:
-
Ireland: Free standard delivery from € 87,90
-
Free
returns More than 10.750 products
We deliver worldwide to
more than 40 countries
Very easy to print with
Rated with 5 out of 5 stars.
One of my go to PLA products for quality/price ratio. Lately it has been made even better with the use of AMS compatible spools.
Was this rating helpful? (0) (0)